News Archives

Pneumatic U-shaped flange butterfly valve

July 22, 2020

Introduction of Pneumatic U-shaped flange butterfly valve:

U type flange butterfly valve (8)

The pneumatic U-shaped butterfly valve adopts a top-mounted structure, which reduces the connecting bolts of the valve body under the conditions of high pressure and large diameter, enhances the reliability of the valve and can overcome the influence of the weight of the system on the normal operation of the valve.

Scope of application of Pneumatic U-shaped flange butterfly valve:
Pneumatic U-shaped butterfly valve is widely used in coal chemical, petrochemical, rubber, paper, pharmacy and other pipelines as media splitting, confluence or flow switching devices.

The main parameters of Pneumatic U-shaped flange butterfly valve:
Nominal diameter of pneumatic U-shaped butterfly valve: DN50mm-DN300mm;

Nominal pressure of pneumatic U-shaped butterfly valve: PN1.0MPa-1.6MPa;

The temperature range of pneumatic U-shaped butterfly valve: -29℃-300℃.

Tanghai Valve is the best manufacturer of U-type butterfly valve in China. We produce the best quality products with competitive low prices.

Tianjin Tanghai Valve Manufacturing Co., Ltd. is one of the largest butterfly valve manufacturers in China, main products are butterfly valves, check valves

Main products: butterfly valve, lug type butterfly valve, wafer type butterfly valve, U-type butterfly valve, double flange butterfly valve, gate valves, check valves, globe valves, valve parts (Valve body, Valve disc, Valve shaft, Valve seat…)

TH Valve is a professional manufacturer of butterfly valve, gate valve, check valve, globe valve, knife gate valve, ball valve with API, JIS, DIN standard, used in Oil, Gas, Marine industry, Water supply and drainage, fire fighting, shipbuilding, water treatment and other systems, with Nominal Diameter of DN50 to DN1200, NBR/EPDM/VITON, Certificates & Approvals: DNV-GL, Lloyds, DNV, BV, API, ABS, CCS. Standards: EN 593, API609, API6D

structure and characteristics of U type flange butterfly valve

July 22, 2020

Introduction of U type flange butterfly valve:
The face-to-face structure of U type flange butterfly valve is shorter than that of double flanged butterfly valve. U-shaped flange butterfly valve is widely used in

U-type flange butterfly valve, ductile iron, DI, center line,

petroleum, chemical, electric power, metallurgy, food, medicine, textile, papermaking and other industries. It can be installed at a temperature of ≤425℃, and the medium is gas, air, steam, water, sea water, Industrial pipe networks such as oil products are used to adjust flow and cut off media.

U-shaped flange butterfly valve drive forms include manual, worm gear, pneumatic, hydraulic, electric, electro-hydraulic linkage and other actuators, which can realize remote control and automatic operation. The structure of the U-shaped flange butterfly valve adopts the principle of three-dimensional knitting design, and the valve seat adopts a multi-level structure compatible with hard and soft sealing, exquisite processing and advanced technology.

Composition and design principle of U type flange butterfly valve:
This product is composed of main components such as valve body, butterfly plate, multi-level valve seat, valve stem and transmission mechanism. Therefore, it is widely used in metallurgy, electric power, petroleum, chemical industry, air, gas, combustible gas, water supply and drainage and other corrosive media pipelines.

Because the U-shaped flange butterfly valve adopts the three-dimensional eccentric principle design, the space motion trajectory of the sealing surface is idealized. There is no friction and interference between the sealing surfaces, and the sealing material is selected properly, so that the sealing performance of the butterfly valve can be improved. Corrosion resistance, high temperature resistance and wear resistance are reliably guaranteed.

Features of U type flange butterfly valve:
The main features of U-shaped flange butterfly valve are:

1. The opening torque is small, flexible and convenient, labor-saving and energy-saving.

2. The three-dimensional knitting core structure makes the butterfly plate tighter and tighter, and its sealing performance is reliable and leak-free.

3. High pressure resistance, corrosion resistance, wear resistance, long service life, etc.

TH Valve is a professional manufacturer of butterfly valve, gate valve, check valve, globe valve, knife gate valve, ball valve with API, JIS, DIN standard, used in Oil, Gas, Marine industry, Water supply and drainage, fire fighting, shipbuilding, water treatment and other systems, with Nominal Diameter of DN50 to DN1200, NBR/EPDM/VITON, Certificates & Approvals: DNV-GL, Lloyds, DNV, BV, API, ABS, CCS. Standards: EN 593, API609, API6D

The structure and application fields of the lug type butterfly valve

July 22, 2020

Product Introduction of lug type butterfly valve:
The driving mode of the lug butterfly valve can be manual, worm gear, pneumatic, electric, hydraulic. The connection method can choose flange and wafer, the

lug type butterfly vlave (15)

structure can choose single eccentric, center line, double eccentric, triple eccentric, and the sealing structure can choose soft seal or hard seal. The pressure range is PN0.1-10Mpa, the nominal diameter is DN40～2000mm, and the material can be cast steel or stainless steel. Due to the wide range of use of valves, the same valve has different combinations in different occasions and working conditions.

The butterfly plate of the lug butterfly valve is installed in the diameter direction of the pipeline. In the cylindrical passage of the butterfly valve body, the disc-shaped butterfly plate rotates around the axis, and the rotation angle is between 0°-90°. When the rotation reaches 90°, the valve is in a fully open state.

Structural features of lug type butterfly valve:

The lug butterfly valve is connected between two pipe flanges with stud bolts. Its structure is simple, small in size, light in weight, and only composed of a few parts. Moreover, it can be opened and closed quickly by rotating 90°, and the operation is simple. At the same time, the valve has good fluid control characteristics. When the butterfly valve is in the fully open position, the thickness of the butterfly plate is the only resistance when the medium flows through the valve body, so the pressure drop produced by the valve is small, so it has better flow control characteristics. The butterfly valve has two sealing types: elastic seal and metal seal. Elastic sealing valve, the sealing ring can be embedded in the valve body or attached to the periphery of the butterfly plate.

Application areas of lug type butterfly valve:
Butterfly valves are not only widely used in general industries such as petroleum, gas, chemical, and water treatment, but also used in cooling water systems of thermal power stations.

Used in the gas pipeline in the sulfuric acid industry: the inlet and outlet of the blower in front of the furnace, the inlet and outlet of the relay fan, the electric demisting series and the connecting valve, the inlet and outlet of the S02 main blower, the adjustment of the converter, the inlet and outlet of the preheater, etc. and the use of cut-off gas.

It is used in the sulfur burning, conversion and dry absorption sections of the sulfur-burning sulphuric acid plant. It is the preferred brand of valves for the sulphur-burning sulphuric acid plant. It is regarded by the majority of users as: good sealing performance, light operation, secondary corrosion, high temperature resistance, convenient operation, The flexible, safe and reliable butterfly valve has been widely used.

Lug butterfly valves are also widely used in: SO2, steam, air, gas, ammonia, CO2, oil, water, brine, lye, seawater, nitric acid, hydrochloric acid in the chemical, petrochemical, smelting, pharmaceutical, food and other industries , Sulfuric acid, phosphoric acid and other medium pipelines are used as regulating and shut-off devices.

Tanghai Valve is the best manufacturer of lug type butterfly valve in China. We produce the best quality products with competitive low prices. Maine products: butterfly valve, lug type butterfly valve, wafer type butterfly valve, U-type butterfly valve, double flange butterfly valve, gate valves, check valves, globe valves, valve parts (Valve body, Valve disc, Valve shaft, Valve seat…)

TH Valve is a professional manufacturer of butterfly valve, gate valve, check valve, globe valve, knife gate valve, ball valve with API, JIS, DIN standard, used in Oil, Gas, Marine industry, Water supply and drainage, fire fighting, shipbuilding, water treatment and other systems, with Nominal Diameter of DN50 to DN1200, NBR/EPDM/VITON, Certificates & Approvals: DNV-GL, Lloyds, DNV, BV, API, ABS, CCS. Standards: EN 593, API609, API6D

Uses and characteristics of manual butterfly valve (2)

July 21, 2020

Uses/application of manual butterfly valve:
Used in the gas pipeline in the sulfuric acid industry: the inlet and outlet of the blower in front of the furnace, the inlet and outlet of the relay fan, the electric demisting series and the connecting valve, the inlet and outlet of the S02 main blower, the adjustment of the converter, the inlet and outlet of the preheater, etc. and

ductile iron, DI, butterfly valve, manufacturer, center line, TH valve

the use of cut-off gas.

It is used in the sulfur burning, conversion and dry absorption sections of the sulfur-burning sulphuric acid plant. It is the preferred brand of valves for the sulphur-burning sulphuric acid plant. It is regarded by the majority of users as: good sealing performance, light operation, secondary corrosion, high temperature resistance, convenient operation, The flexible, safe and reliable butterfly valve has been widely used.

It is also widely used in: SO2, steam, air, gas, ammonia, CO2, oil, water, brine, lye, seawater, nitric acid, hydrochloric acid, sulfuric acid, phosphoric acid in the chemical, petrochemical, smelting, pharmaceutical, food and other industries It is used as a regulating and intercepting device on the pipeline of other medium.

Structural features of manual butterfly valve:

The unique design of three-way eccentricity enables frictionless transmission between the sealing surfaces and prolongs the service life of the valve.
Elastic seal is produced by torque.
The clever wedge-shaped design enables the valve to have an automatic sealing function that is tighter and tighter, and the sealing surfaces are compensated and leak-free.
Small size, light weight, light operation and easy installation.
Pneumatic and electric devices can be configured according to user requirements to meet the needs of remote control and program control.
The material of replacement parts can be applied to various media, and can be lining anti-corrosion (lining F46, GXPP, PO, etc.).
Diversified continuous structure: wafer, flange, butt welding.

Tianjin TanghaiDongyang Valve Co., Ltd. is one of the largest butterfly valve manufacturers in China, main products are butterfly valves, check valves.

TH Valve is a professional manufacturer of butterfly valve, gate valve, check valve, globe valve, knife gate valve, ball valve with API, JIS, DIN standard, used in Oil, Gas, Marine industry, Water supply and drainage, fire fighting, shipbuilding, water treatment and other systems, with Nominal Diameter of DN50 to DN1200, NBR/EPDM/VITON, Certificates & Approvals: DNV-GL, Lloyds, DNV, BV, API, ABS, CCS. Standards: EN 593, API609, API6D

Uses and characteristics of manual butterfly valve (1)

July 21, 2020

The butterfly plate of the manual butterfly valve is installed in the diameter direction of the pipeline. In the cylindrical passage of the butterfly valve body, the disc-shaped butterfly plate rotates around the axis, and the rotation angle is between 0°-90°. When the rotation reaches 90°, the valve is fully opened. The butterfly valve is simple in structure, small in size and light in weight, and consists of only a few parts. Moreover, it can be opened and closed quickly by rotating 90°, and the

manual Wafer type butterfly valve with worm gear

operation is simple. At the same time, the valve has good fluid control characteristics.

Introduction of manual butterfly valve:
The butterfly plate of the butterfly valve is installed in the diameter direction of the pipe. In the cylindrical passage of the butterfly valve body, the disc-shaped butterfly plate rotates around the axis, and the rotation angle is between 0°-90°. When the rotation reaches 90°, the valve is fully opened.

The butterfly valve is simple in structure, small in size and light in weight, and consists of only a few parts. Moreover, it can be opened and closed quickly by rotating 90°, and the operation is simple. At the same time, the valve has good fluid control characteristics. When the butterfly valve is in the fully open position, the thickness of the butterfly plate is the only resistance when the medium flows through the valve body, so the pressure drop generated by the valve is small, so it has better flow control characteristics. Butterfly valves have two sealing types: elastic seal and metal seal. Elastic sealing valve, the sealing ring can be embedded in the valve body or attached to the periphery of the butterfly plate.

Valves with metal seals generally have a longer life than valves with elastic seals, but it is difficult to achieve a complete seal. Metal seals can adapt to higher operating temperatures, while elastic seals have the defect of being limited by temperature.

If the butterfly valve is required to be used as a flow control, the main thing is to correctly select the size and type of the valve. The structure principle of the butterfly valve is especially suitable for making large diameter valves. Butterfly valves are not only widely used in general industries such as petroleum, gas, chemical, and water treatment, but also used in cooling water systems of thermal power stations.

Commonly used butterfly valves include wafer butterfly valves and flange butterfly valves. Wafer type butterfly valve uses double-head bolts to connect the valve between two pipe flanges. Flange type butterfly valve has flanges on the valve, and bolts are used to connect the flanges at both ends of the valve to the pipe flanges.

TH Valve is a professional manufacturer of butterfly valve, gate valve, check valve, globe valve, knife gate valve, ball valve with API, JIS, DIN standard, used in Oil, Gas, Marine industry, Water supply and drainage, fire fighting, shipbuilding, water treatment and other systems, with Nominal Diameter of DN50 to DN1200, NBR/EPDM/VITON, Certificates & Approvals: DNV-GL, Lloyds, DNV, BV, API, ABS, CCS. Standards: EN 593, API609, API6D

Installation instructions of the wafer type butterfly valve

July 21, 2020

Preparation before installation of wafer type butterfly valve:
1. Check whether the specifications and materials of the butterfly valve conform to the design before installation.

wafer type butterfly valve, EPDM seat (10)

2. Before installation, clean the internal sand, dust, foreign matter and debris to avoid irregular movement or leakage.
3. The related piping should be properly suspended and fixed according to regulations before installation to avoid improper stress on the valve after installation.
4. The two flange faces of the piping must be aligned parallel and concentric.
5. No additional gasket is needed between butterfly valve and flange during installation.
6. Where the butterfly valve is close to the check valve or the pump, use a divergent joint between the two so that the valve disc will not be hindered from turning off.

Installation steps of wafer type butterfly valve:
1. Open the valve disc 10 degrees before installation. (The same before disassembly)
2. Set auxiliary screws at appropriate positions to adjust the distance between the two flange surfaces.
3. Insert the butterfly valve without touching the two flange surfaces and at the same time penetrate the remaining bolts.
4. After confirming that the center of the butterfly valve is concentric with the center of the flange and the switch position of the valve disc is not the inner diameter of the flange or the adjacent parts are obstructed, the bolts are locked repeatedly in a diagonal and gradual manner until the flange surface touches the end surface of the valve body.
5. After the installation is completed, the degree of full open and full close should be confirmed again.

Operation:
1. Before starting the operation, use air spray to remove foreign objects on the piping, and clean the inner surface of the piping with clean water.
2. Open the valve to check the angle indicator plate, avoid torsion exceeding the opening width, and the closing position cannot be exceeded.
3. The operation of the switch is completely based on the indicator. If other hand tools are applied, the angle indicating plate and the switch will be damaged.
4. When the pressure test of piping is to be done, the valve should be opened.
5. After piping, the valve is in a fully closed state for a long time, and it should be switched on and off once or twice a month to avoid fixation.

Tianjin Tanghaidongyang Co., Ltd. is one of the largest butterfly valve manufacturers in China, main products are butterfly valves, check valves. main products: butterfly valve, lug type butterfly valve, wafer type butterfly valve, U-type butterfly valve, double flange butterfly valve, gate valves, check valves, globe valves, valve parts (Valve body, Valve disc, Valve shaft, Valve seat…)

TH Valve is a professional manufacturer of butterfly valve, gate valve, check valve, globe valve, knife gate valve, ball valve with API, JIS, DIN standard, used in Oil, Gas, Marine industry, Water supply and drainage, fire fighting, shipbuilding, water treatment and other systems, with Nominal Diameter of DN50 to DN1200, NBR/EPDM/VITON, Certificates & Approvals: DNV-GL, Lloyds, DNV, BV, API, ABS, CCS. Standards: EN 593, API609, API6D

The structural characteristics and uses of the wafer butterfly valve

July 20, 2020

The structural characteristics and uses of the wafer type butterfly valve:

wafer type butterfly valve, NBR seat (11)

The unique design of three-way eccentricity enables frictionless transmission between the sealing surfaces and prolongs the service life of the valve.
The elastic seal is produced by torque.
The ingenious wedge-shaped design makes the valve have an automatic sealing function as the valve is closed and tighter, and the sealing surface has compensation and zero leakage.
Small size, light weight, light operation, easy to install.
Pneumatic and electric devices can be configured according to user requirements to meet the needs of remote control and program control.
The material of the replacement parts can be applied to various media, and the lining can be anticorrosive (lining F46, GXPP, PO, etc.)
Diversified continuous structure: butt clamp, flange, butt welding.

Used in the gas pipeline in the sulfuric acid industry: the inlet and outlet of the blower in front of the furnace, the inlet and outlet of the relay fan, the electric demisting series and the connecting valve, the inlet and outlet of the S02 main blower, the adjustment of the converter, the inlet and outlet of the preheater, etc. and the use of cut-off gas.
It is used in the sulfur burning, conversion and dry absorption sections of the sulfur-burning sulphuric acid plant. It is the preferred brand of valves for the sulphur-burning sulphuric acid plant. It is regarded by the majority of users as: good sealing performance, light operation, secondary corrosion, high temperature resistance, convenient operation, The flexible, safe and reliable butterfly valve has been widely used.
It is also widely used in: SO2, steam, air, gas, ammonia, CO2, oil, water, brine, lye, seawater, nitric acid, hydrochloric acid, sulfuric acid, phosphoric acid in the chemical, petrochemical, smelting, pharmaceutical, food and other industries It is used as a regulating and intercepting device on the pipeline of other medium.

Tianjin Tanghaidongyang valve Co., Ltd. is one of the largest butterfly valve manufacturers in China, main products are butterfly valves, check valves. Main products: butterfly valve, lug type butterfly valve, wafer type butterfly valve, U-type butterfly valve, double flange butterfly valve, gate valves, check valves, globe valves, valve parts (Valve body, Valve disc, Valve shaft, Valve seat…)

TH Valve is a professional manufacturer of butterfly valve, gate valve, check valve, globe valve, knife gate valve, ball valve with API, JIS, DIN standard, used in Oil, Gas, Marine industry, Water supply and drainage, fire fighting, shipbuilding, water treatment and other systems, with Nominal Diameter of DN50 to DN1200, NBR/EPDM/VITON, Certificates & Approvals: DNV-GL, Lloyds, DNV, BV, API, ABS, CCS. Standards: EN 593, API609, API6D

Comparison and analysis of the performance of the wafer butterfly valve

July 20, 2020

With the same nominal pressure and nominal diameter, ordinary which has better tightness and is not easy to leak? butterfly valve or gate valve?

wafer type butterfly valve, NBR seat (11)

The airtightness of the gate valve is better than that of the butterfly valve, but there are also manufacturers’ butterfly valves that have better airtightness.
The gate valve is large in size and takes up a lot of space.
The butterfly valve is small in size and takes up little space.

When selecting concretely, the temperature of the medium, the sealing of the valve and the packing should also be considered.
The specification stipulates that the butterfly valve with a nominal diameter greater than 50 is used.

Wafer butterfly valve is a national key new product. The high-performance manual butterfly valve adopts a double eccentric and a special oblique cone oval sealing structure. It solves the shortcoming of the traditional eccentric butterfly valve that the sealing surface is still in sliding contact friction at the moment of opening and closing 0°～10°, and the sealing surface of the butterfly plate is separated at the moment of opening, and the effect of sealing when the contact is closed is achieved to extend the service life and maximize the sealing performance.

Tanghai Valve is the best manufacturer of wafer-type butterfly valve in China. We produce the best quality products with competitive low prices.

13 gate-valve-5

Our products use advanced manufacturing technology, and strictly conform to API, DIN, BS, EN, GB and other international standards. The main products are butterfly valves, gate valves, check valves, globe valves, valve parts (Valve body, Valve disc, Valve shaft, Valve seat…), etc. Our products are widely used in various fields such as marine industry, shipbuilding, petrochemical, metallurgy, water treatment, fire fighting, water supply and drainage, etc. The company has won unanimous recognition and praise from customers with high quality and good reputation.

We have established long-term and stable business relationships with many multinational companies. Our products are exported to Europe, the United States, Australia, and the Middle East, Southeast Asia and other countries and regions. The quality of our products has been widely recognized by customers, and has been trusted and praised by customers. Gradually we have established a close technical partnership with customers from various countries.

We are committed to “Build a top valve enterprise; Be a reliable partner!”

Friends from all over the world are welcome to visit us for evaluation, guidance, and orders!

TH Valve is a professional manufacturer of butterfly valve, gate valve, check valve, globe valve, knife gate valve, ball valve with API, JIS, DIN standard, used in Oil, Gas, Marine industry, Water supply and drainage, fire fighting, shipbuilding, water treatment and other systems, with Nominal Diameter of DN50 to DN1200, NBR/EPDM/VITON, Certificates & Approvals: DNV-GL, Lloyds, DNV, BV, API, ABS, CCS. Standards: EN 593, API609, API6D

What is a wafer type butterfly valve

July 20, 2020

The butterfly valve plate of the wafer type butterfly valve is installed in the diameter direction of the pipeline. In the cylindrical passage of the butterfly valve body,

Wafer type butterfly valve with worm gear

the disc-shaped butterfly plate rotates around the axis, and the rotation angle is between 0°-90°. When the rotation reaches 90°, the valve is fully opened. This valve is generally installed horizontally. The wafer butterfly valve is simple in structure, small in size and light in weight, and consists of only a few parts. Moreover, it can be opened and closed quickly by rotating 90°, and the operation is simple. At the same time, the valve has good fluid control characteristics.

When the wafer type butterfly valve is in the fully open position, the thickness of the butterfly plate is the only resistance when the medium flows through the valve body, so the pressure drop generated by the valve is small, so it has better flow control characteristics. The butterfly valve has two sealing types: elastic seal and metal seal. Elastic sealing valve, the sealing ring can be embedded in the valve body or attached to the periphery of the butterfly plate.

Valves with metal seals generally have a longer life than valves with elastic seals, but it is difficult to achieve a complete seal. Metal seals can adapt to higher operating temperatures, while elastic seals have the defect of being limited by temperature.

If the wafer type butterfly valve is required to be used as a flow control, the main thing is to correctly select the size and type of the valve. The structure principle of the butterfly valve is especially suitable for making large diameter valves. Butterfly valves are not only widely used in general industries such as petroleum, gas, chemical, and water treatment, but also used in cooling water systems of thermal power stations.

Commonly used butterfly valves include wafer butterfly valves and flanged butterfly valves. Wafer type butterfly valve uses double-head bolts to connect the valve between two pipe flanges. Flange type butterfly valve has flanges on the valve, and bolts are used to connect the flanges at both ends of the valve to the pipe flanges.

Tianjin Tanghai Valve Manufacturing Co., Ltd. is one of the largest butterfly valve manufacturers in China, main products are butterfly valves, check valves. The Key products: butterfly valve, lug type butterfly valve, wafer type butterfly valve, U-type butterfly valve, double flange butterfly valve, gate valves, check valves, globe valves, valve parts (Valve body, Valve disc, Valve shaft, Valve seat…)

TH Valve is a professional manufacturer of butterfly valve, gate valve, check valve, globe valve, knife gate valve, ball valve with API, JIS, DIN standard, used in Oil, Gas, Marine industry, Water supply and drainage, fire fighting, shipbuilding, water treatment and other systems, with Nominal Diameter of DN50 to DN1200, NBR/EPDM/VITON, Certificates & Approvals: DNV-GL, Lloyds, DNV, BV, API, ABS, CCS. Standards: EN 593, API609, API6D

Notes on selection and installation of butterfly valve

July 17, 2020

Product selection points of butterfly valves:
1. The main control parameter of the butterfly valve is the size.
2. The butterfly valve is a single-plate air valve. It has a simple structure, convenient processing, low cost, and easy operation, but the adjustment accuracy is poor. It

ductile iron, DI, butterfly valve, manufacturer, center line, TH valve

is only suitable for the occasion of switching or rough adjustment in the ventilation and air conditioning system.
3. It can be operated manually, electrically or by zipper, and can be fixed at any angle in the range of 90°.
4. Due to the single shaft and single valve plate, the bearing capacity is limited, and the service life of the valve is short under the condition of large pressure difference and large flow rate. The valve is divided into closed type and ordinary type, thermal insulation and non-thermal insulation.
5. The electric butterfly valve has only two-position control, and the electric actuator is the same as the multi-leaf valve.

Installation matters of butterfly valve:
The butterfly valve has a simple structure, small volume, light weight, and relatively few components. The key parts can form a butterfly valve. It is also very convenient to open. You only need to select the switch to ninety degrees. The butterfly valve The fluid control is very good, you can increase or decrease the flow at any time, the valve has a certain resistance when transporting any fluid, and the resistance of the butterfly valve mainly comes from its own, such as the thickness of the butterfly valve body, if you want to reduce the fluid The resistance only needs to reduce its thickness.
Elastic seals have the disadvantage of being limited by temperature.
Butterfly valves are also widely used. If they are used to control the flow rate, different types and sizes of valve bodies need to be selected, because butterfly valves are more suitable for valves with larger diameters when they are designed. Butterfly valves are not only widely used in general industries such as petroleum, gas, chemical, and water treatment, but also in cooling water systems of thermal power stations.

Tianjin Tanghai dongyang valve Co., Ltd. is one of the largest butterfly valve manufacturers in China, main products are butterfly valves, check valves. Product ranges: butterfly valve, lug type butterfly valve, wafer type butterfly valve, U-type butterfly valve, double flange butterfly valve, gate valves, check valves, globe valves, valve parts (Valve body, Valve disc, Valve shaft, Valve seat…)

TH Valve is a professional manufacturer of butterfly valve, gate valve, check valve, globe valve, knife gate valve, ball valve with API, JIS, DIN standard, used in Oil, Gas, Marine industry, Water supply and drainage, fire fighting, shipbuilding, water treatment and other systems, with Nominal Diameter of DN50 to DN1200, NBR/EPDM/VITON, Certificates & Approvals: DNV-GL, Lloyds, DNV, BV, API, ABS, CCS. Standards: EN 593, API609, API6D

Pneumatic U-shaped flange butterfly valve

structure and characteristics of U type flange butterfly valve

The structure and application fields of the lug type butterfly valve

Uses and characteristics of manual butterfly valve (2)

Uses and characteristics of manual butterfly valve (1)

Installation instructions of the wafer type butterfly valve

The structural characteristics and uses of the wafer butterfly valve

Comparison and analysis of the performance of the wafer butterfly valve

What is a wafer type butterfly valve

Notes on selection and installation of butterfly valve

TH VALVE • PROFESSIONAL VALVE MANUFACTURER

GET IN TOUCH WITH US